What size wire do I need for a 125 amp breaker?

With 75 °C terminations, 1 AWG copper or 2/0 AWG aluminum (NEC Table 310.16). With 60 °C terminations, 1/0 AWG copper. Long runs may need a size up for voltage drop.

Can I use 1 AWG THHN copper on 125 amps?

Yes: 1 AWG is the answer at both 75 °C and 90 °C, because the 90 °C column may only be used for derating; the termination (110.14(C)) caps the conductor at its 75 °C value.

How far can 1 AWG copper run on a 125 amp circuit?

At 80 % load (100 A) and the 3 % informational note, about 117 ft one-way at 120 V and 234 ft at 240 V by the K-factor method. Beyond that, go up a size.

What size wire for 125 amps?

1 AWG copper or 2/0 AWG aluminum with 75 °C terminations, by NEC Table 310.16 at 30 °C with no more than three current-carrying conductors. Subpanels and small services; large heat pumps.

Minimum conductor size

Minimum size · copper1AWGFITS75 °C insulation on 75 °C terminations · needs 125 A at 30 °C ambient with 3 current-carrying conductors · NEC 2023 Table 310.16

Load current

The load, or the breaker rating you must feed

Conductor

Continuous load

Table 310.16 ampacity, 1 AWG at 75 °CNEC 2023 Table 310.16, identical to 2017 Table 310.15(B)(16): 130 A
After correction and adjustment× 1.00 for 30 °C (NEC 2023 Table 310.15(B)(1)(1)) × 1.00 for 3 conductors (NEC 2023 Table 310.15(C)(1)): 130.0 A
Termination cap, 110.14(C) at 75 °CCircuits > 100 A or larger than 1 AWG use the 75 °C column: 130 A
Usable ampacitythe smallest of the three above: 130.0 A

Ampacity from NEC 2023 Table 310.16 (identical to 2017 Table 310.15(B)(16)), corrected for ambient and conductor count, capped by the termination rating (110.14(C)) and the small-conductor limits of 240.4(D). Equipment listings, conductor markings and local amendments govern; a licensed electrician makes the final call.

Insulation rating

Termination rating

Ambient temperature

30 °C is the table base; attics and rooftops run hotter

Current-carrying conductors

In the same raceway or cable; 3 or fewer needs no adjustment

Length, one-way (optional)

Adds a voltage-drop check against the 3 % note

Voltage

For the drop check

Phase

Nothing typed leaves the browser; the inputs live only in the page address.

Every column for 125 A

Conductor and terminations	Size	Usable ampacity	Why
Copper, 60 °C (TW, UF; or unmarked equipment ≤ 100 A)	1/0 AWG	125 A	Table 310.16, 125 A
Copper, 75 °C (THW, THWN, XHHW; marked 75 °C terminations)	1 AWG	130 A	Table 310.16, 130 A
Copper, 90 °C insulation on 75 °C terminations (THHN)	1 AWG	130 A	capped at the 75 °C column (110.14(C))
Aluminum, 75 °C	2/0 AWG	135 A	Table 310.16, 135 A
Aluminum, 90 °C insulation on 75 °C terminations (XHHW-2)	2/0 AWG	135 A	capped at the 75 °C column (110.14(C))
Copper, 75 °C, continuous load at 80 % of the breaker (100 A × 1.25)	1 AWG	130 A	210.19(A)(1): a continuous load is sized at 125 %

How far it can run

K-factor method at 80 % load (100 A), single-phase, one-way length for a 3 % drop (an informational note, not a requirement), and the drop at 100 ft.

Conductor	Voltage	3 % reached at	Drop at 100 ft
1 AWG copper	120 V	117 ft	2.6 %	open
1 AWG copper	240 V	234 ft	1.3 %	open
2/0 AWG aluminum	120 V	113 ft	2.7 %	open
2/0 AWG aluminum	240 V	226 ft	1.3 %	open

Questions people ask

What size wire do I need for a 125 amp breaker?: With 75 °C terminations, 1 AWG copper or 2/0 AWG aluminum (NEC Table 310.16). With 60 °C terminations, 1/0 AWG copper. Long runs may need a size up for voltage drop.
Can I use 1 AWG THHN copper on 125 amps?: Yes: 1 AWG is the answer at both 75 °C and 90 °C, because the 90 °C column may only be used for derating; the termination (110.14(C)) caps the conductor at its 75 °C value.
How far can 1 AWG copper run on a 125 amp circuit?: At 80 % load (100 A) and the 3 % informational note, about 117 ft one-way at 120 V and 234 ft at 240 V by the K-factor method. Beyond that, go up a size.